Logo Logo-bar
Thompson Automotive Labs
Categories
Diagnostic Tools & Software (8)
Fuel Injection Testing & Cleanin (5)
Scan Tools (15)
Training Materials (14)
ACE Detective Kit-> (8)
Accessories-> (27)
Labscopes (6)
Manufacturers
What's New?


Engine Tech 2200

Fuel ZAPP FSA

Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
Information
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us
 
 

 

Lab Scope Accessories

 

3M Test Lead $40.00 Purchase Test LeadsTest Leads

The TA000 test lead has been custom made for automotive use with Pico Automotive Lab Scope. Its length (3 meters — approx 10 ft) allows the lab scope to be placed on the work bench away from the car being tested or repaired. A wide range of probes, clips and gators can be plugged into the 4 mm connectors at the end of the cable.

 

 

Piercing ProbesPiercing Test Clips $50.00  Piercing Probes

The insulation piercing test clips allow the user to provide the exact pressure needed to pierce the insulation of a wide range of wire types and sizes. The clips also feature a rotating banana jack that prevents the test lead from twisting and allows the test equipment to be kept in the circuit while the wire is pierced, providing immediate confirmation that contact with the conductor has been made.

 

Multimeter ProbesMultimeter Probes $7.36   

 This multimeter lab scope probe offers a quick and easy solution, where a permanent connection is not required. The 4 mm socket in the handle of the probe connects straight into the TA000 test lead


         Red Multimeter Probes Purchase 20:1 Attenuator    Black  Multimeter Probes Purchase 20:1 Attenuator

Small CrocSmall Crocodile (Gator) Clips $5.52

These lab scope accessory crocodile clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the TA000 test lead. The toothed grip offers good contact on fine wire, with a 11 mm jaw opening limit.

 


         Red Small Croc Purchase 20:1 Attenuator    Black  Small Croc Purchase 20:1 Attenuator

 

Large CrocLarge Dolphin (Gator) Clips $9.20

These lab scope accessory crocodile clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the TA000 test lead. The toothed grip offers good contact on fine wire, with a 30 mm jaw opening limit.


   Red Large Croc Purchase 20:1 Attenuator    Black  Large Croc Purchase 20:1 Attenuator

 

Acupuncture Probe Set  $58.00 Purchase 20:1 Attenuator Acupuncture Probe Set

 First and foremost the TA008 is a back pinning probe. In fact, it's the smallest diameter back pinning probe that we know of. This is essential for probing today's small, fragile connector. It is also very sharp, so it slides past connector seals with ease. This product solves most of the problems associated with traditional lab scope back-pinning methods.

The TA008 is a Piercing probe
Secondly, the TA008 is a piercing probe. Its small diameter, extra sharp pin makes it ideal for piercing the insulation on small gauge wires where traditional piercing tools might cause damage.

The TA008 is field repairable
And finally, here's the best part. Don't you just hate it when you are using a back pinning probe and it bends or breaks? Before the TA008 came along, this meant that you had to buy a whole new back-probe. Not with the TA008; it's repairable. If the pin becomes damaged or useless in any way, simply take your pocket screwdriver, remove the set screw, pull out the old pin and install the new one! There's no need to replace the whole probe.

 

20:1 Attenuator  $80.00 Purchase 20:1 Attenuator

20:1 AttenuatorThe PP198 has been designed to allow fuel injector and primary ignition waveforms to be measured using Pico lab scope products.

 
Specifications
Attenuation 20:1
Input Impedance 1.053 MΩ
Input capacitance 11 pF
Bandwidth 100 MHz (-3 dB)
Max input 300 V

                                        

 The PP198 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the PP198 allows voltages higher than the ±20 V input range of the Pico lab scope to be measured.

   
 

The PP198, when used with Pico PC lab scope provides increased input protection against overloads when working with inductive signals such as injectors and primary ignition. Under no circumstances attempt to use this attenuator to measure secondary ignition (HT) waveforms, the PP178 Secondary Ignition Pickup lead should be used for this purpose.

 

BNC Plug to Banana Adapter $17.50

Adapts lab scope banana inputs to a bnc output.

 

 Coil -on-plug Ignition Probe $186.00 

COP Ignition ProbeGives scope patterns of the secondary, faster than scoping the secondary
Works on all lab scopes capable of displaying ignition patterns
Suitable for use on most COP and conventional ignition systems
Long probe (36 cm / 14 inches including handle)
No batteries required

 

 BNC to BNC with Earth Clamp $29.00 

This 3 meter BNC to BNC lab scope cable includes an earth cable to protect your scope from high voltage leaks from the ignition system. BNC connectors feature insulating rubber boots and cable strain relief to protect the cable.
Cable length: 3 m (9.8 ft)
Earth cable length: 1.5 m
Earth cable position: 1.5 m from each end

 

 Coil -on-plug Ignition Probe + Cable $189.00 

Coil-on-plug+bnc

 

 *pp357 kit Saves $17.00 *

 

Designed to save you time, effort and money, our the Coil-On-Plug ignition probe is a fast way to test both conventional and Coil-On-Plug secondary ignition systems. Comes with a 3 meter BNC to BNC cable that includes an earth cable to protect your lab scope from high voltage leaks from the ignition system. BNC connectors feature insulating rubber boots and cable strain relief to protect the cable.

Mixmaster 12-Channel Automotive Signal Mixer $355.00

 

Mixmaster

 

 

 With the Mixmaster 12-channel automotive signal mixer you can view an ignition parade display of up to 12 cylinders on any lab scope.

Mixmaster can produce a parade display of up to 12 cylinders using a single channel of your lab scope. If you have a 2-channel scope, then Mixmaster can also display 2 engine banks separately with up to 6 cylinders per bank.

Mixmaster includes a trigger output, derived from one of the 12 input signals, which can be used to synchronise the scope to a known cylinder. Additionally, Mixmaster features a simple switch so you can invert a bank of signals to deal with negative-going “wasted spark” signals.

Designed for use with the Automotive Lab Scope Kit, Mixmaster can also be used on virtually any other lab scope, and can be used on both DIS and distributor ignition systems.
Mixmaster is supplied with 3 BNC leads to connect to the oscilloscope, an engine-block ground lead, and a set of 4 short secondary ignition leads. Additional packs of secondary ignition leads can be purchased separately below.

Mixmaster Secondary Ignition Pickup (4-Pack) $99.00


Mixmaster Ignition LeadsA pack of 4 secondary ignition pickups is available for use with Mixmaster. Each lead is approximately 40 cm / 15 in long. These leads do not include an earth clip. If desired, the longer PP178 Secondary Ignition Lab Scope Pickups listed below can also be used.

 

 
Secondary Ignition Pickup $65.00 (each) Secondary Ignition Pickup

 

 Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection, attempting to make a direct connection will almost certainly damage the measuring instrument.

The PP178 is a capacitive pickup which simply connects around the insulation of an ignition circuit component such as a plug wire, this avoids the need for direct connection of your lab scope.

The PP178 comes with a shielded 1.8m (6 foot) lead. It is suitable for use with conventional ignition systems and most HEI and DIS systems.

Inductive Sync Probe $54.00

 

Inductive Synch Probe

 

 

 

This lab scope probe allows for accurate triggering of scope display from spark plug wire signals. You can organize your display by triggering from #1 plug wire. This trigger probe connects to an input channel on your scope (normally channel one). Use this inductive trigger pickup on digital lab scopes with banana plug inputs.

 

 60 Amp Current Clamp

 

 60 amp current clamp $98.00

 

The TAL-0760 current clamp is ideal for use with any automotive lab scope for measuring currents between 10 mA and 60 A. This enables the scope to display current waveforms for fuel injectors and fuel pumps.
 
The current clamp has two calibration settings, set by a slider switch on the handle of the probe.

                    1 mV/10 mA (100 mV = 1 A)
— use this for testing currents up to 20A
                    1 mV/100 mA (10 mV = 1 A) — use this for testing current up to 60A.
In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.

 

600 amp current clamp $98.00

 

600 Amp Current ClampThe TAL-07600 current clamp can measure currents up to 600 A for both AC (up to 400 Hz) and DC currents. Features includes a low battery indicator. Supplied with 4 mm (banana) plug type connectors.

The current clamp can measure up to 600 A (AC or DC). In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.
 

 

 

 

 


 
 
©2006-2017 Thompson Automotive Labs                                    Home | Catalog | News | Contact Us | Forums | Support